Time limit: 0
Quiz-summary
0 of 23 questions completed
Questions:
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
Information
CCNA 3 v6.0 Chapter 8 Exam
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading...
You must sign in or sign up to start the quiz.
You have to finish following quiz, to start this quiz:
Results
0 of 23 questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 points, (0)
| Average score |
|
| Your score |
|
Categories
- Not categorized 0%
Your result has been entered into leaderboard
![captcha]()
Loading
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- Answered
- Review
-
Question 1 of 23
1. Question
1 pointsWhat is used to create the OSPF neighbor table?
Correct
Incorrect
-
Question 2 of 23
2. Question
1 pointsWhich OSPF component is identical in all routers in an OSPF area after convergence?
Correct
Incorrect
-
Question 3 of 23
3. Question
1 pointsWhich OPSF packet contains the different types of link-state advertisements?
Correct
Incorrect
-
Question 4 of 23
4. Question
1 pointsWhat happens immediately after two OSPF routers have exchanged hello packets and have formed a neighbor adjacency?
Correct
Incorrect
-
Question 5 of 23
5. Question
1 pointsWhat will an OSPF router prefer to use first as a router ID?
Correct
Incorrect
-
Question 6 of 23
6. Question
2 pointsWhat are the two purposes of an OSPF router ID? (Choose two.)
Correct
Incorrect
-
Question 7 of 23
7. Question
1 pointsBy default, what is the OSPF cost for any link with a bandwidth of 100 Mb/s or greater?
Correct
Incorrect
-
Question 8 of 23
8. Question
1 pointsWhich command should be used to check the OSPF process ID, the router ID, networks the router is advertising, the neighbors the router is receiving updates from, and the default administrative distance?
Correct
Incorrect
-
Question 9 of 23
9. Question
2 pointsWhat are two reasons that will prevent two routers from forming an OSPFv2 adjacency? (Choose two.)
Correct
Incorrect
-
Question 10 of 23
10. Question
3 pointsWhich three addresses could be used as the destination address for OSPFv3 messages? (Choose three.)
Correct
Incorrect
-
Question 11 of 23
11. Question
1 pointsA network administrator enters the command ipv6 router ospf 64 in global configuration mode. What is the result of this command?
Correct
Incorrect
-
Question 12 of 23
12. Question
1 pointsWhen a network engineer is configuring OSPFv3 on a router, which command would the engineer issue immediately before configuring the router ID?
Correct
Incorrect
-
Question 13 of 23
13. Question
1 pointsSingle area OSPFv3 has been enabled on a router via the ipv6 router ospf 20 command. Which command will enable this OSPFv3 process on an interface of that router?
Correct
Incorrect
-
Question 14 of 23
14. Question
1 pointsWhat does a Cisco router use automatically to create link-local addresses on serial interfaces when OSPFv3 is implemented?
Correct
Incorrect
-
Question 15 of 23
15. Question
1 pointsWhich command will verify that a router that is running OSPFv3 has formed an adjacency with other routers in its OSPF area?
Correct
Incorrect
-
Question 16 of 23
16. Question
1 pointsWhich command will provide information specific to OSPFv3 routes in the routing table?
Correct
Incorrect
-
Question 17 of 23
17. Question
7 pointsMatch the OSPF state with the order in which it occurs. (Not all options are used.)
Place the options in the following order:
Sort elements
- second state
- seventh state
- fifth state
- first state
- fourth state
- third state
- sixth state
-
Init state
-
Full state
-
Exchange state
-
Down state
-
Exstart state
-
Two-way state
-
Loading state
Correct
Incorrect
-
Question 18 of 23
18. Question
4 pointsMatch each OSPF packet type to how it is used by a router. (Not all options are used.)
Sort elements
- hello packet
- link-state update packet
- database description packet
- link-state request packet
-
establish and maintain adjacencies
-
advertise new information
-
compare local topology to that sent by another router
-
query another router for additional information
Correct
Incorrect
-
Question 19 of 23
19. Question
4 pointsBy order of precedence, match the selection of router ID for an OSPF-enable router to the possible router ID options. (Not all option are used.)
Sort elements
- Third precedence
- Fourth precedence
- First precedence
- Second precedence
-
loopback interface address 10.1.1.1
-
Serial interface IP address 192.168.10.1
-
Configured router ID 1.1.1.1
-
Loopback interface IP address 172.16.1.1
Correct
Incorrect
-
Question 20 of 23
20. Question
4 pointsMatch the information to the command that is used to obtain the information. (Not all options are used.)
Sort elements
- Neighbor ID of 3.3.3.3
- Routing Process “ospf 10” with ID 1.1.1.1
- Routing Protocol is “ospf 10”
- BW 1544 Kbit/sec
-
show ip ospf neighbor
-
show ip ospf
-
show ip protocols
-
show interface serial 0/0/0
Correct
Incorrect
-
Question 21 of 23
21. Question
1 pointsFill in the blank.
- OSPF uses (cost, COST) as a metric.
Correct
Incorrect
-
Question 22 of 23
22. Question
1 pointsFill in the blank.
- The election of a DR and a BDR takes place on (multiaccess, MULTIACCESS) networks, such as Ethernet networks.
Correct
Incorrect
-
Question 23 of 23
23. Question
1 pointsOpen the PT Activity. Perform the tasks in the activity instructions and then complete the task.
What message is displayed on http://www.ciscoville.com?
Correct
Incorrect
